熱水器加壓馬達掌心雷加壓馬達加壓泵加壓泵浦加壓器馬達加壓幫浦

Pump Motor water pump water tap bath room tape hot water pump
熱水器加壓馬達, 加壓馬達加壓泵, 加壓泵浦加壓器 , 馬達, 無聲, 無噪音, 靜音, 超靜音加壓馬達
泵浦, 加壓機, 穩壓馬達熱水加壓泵浦熱水增壓器, 熱水加壓泵, 熱水加壓器, 加壓幫浦, 忽冷忽熱 Times New Roman; color: #029779">, #029779"> font-family: Times New Roman; color: #029779">,

EagleFly® Hot Water Pump PumpTW CHINA cn

Palm Thunder Pump 24VDC

The pump body is manufactured with engineering plastic injection.
Improved engineering plastic pressure vanes, more resistant to high water temperatures,
Using a magnetic floating axis that adapts to the worldwide environment, 24VDC DC drive save use (head: 13.5 meters).

Must buy palms, purchase focus:

1. The price is affordable, and the spare parts are installed.
Just install the tool: a 14mm fixed wrench and
Each of the #200 and #250 wrenches can be installed to solve the water troubles.

2. DC 24V power saving 65W (electric vehicle) power, large lift 13.50 meters,
function is greater than
Generally 110V-220V AC 120W pressure motor.

3. Good waterproof, DC drive, high torque, safe and non-electrical.

4. A large flow rate of 20 liters per minute is enough to drive the water output
of the 16 liter water heater.

5. Quiet, start, pressurize, no sound, true DIY enjoy the achievements.

6. Pocket type, mini size, placed everywhere, no dead ends installed.

7. With motor mount (including fixed stainless steel screws, plastic gecko),
copper adapters, hoses, gaskets,
Stop venting tape, easy to disassemble the movable steel pipe clamp,
do not need to find another installation spare parts (one purchase), you can go straight.

8. The seller has been operating the pump for 10 years and has
1000 questions: the Q&A page can be inquired and can be called at any time.
Customer service installation water consultation, straight installation without troubles.

9. The product is guaranteed for one year.

15MX-12NP Palm Size Thunder Pump 24VDC 65W

Safe DC 24VDC power supply, the most refined, small size, high horsepower,
DC (No electric shock) Brushless pump
15MX-12NP palm thunder pump with engineering plastic pump body, no rust water,
pure copper motor, DC enhanced horsepower 65W (Head 13.5 meters).
Inner canal flow sensor switch, magnetic floating water cooling shaft design, air-to-air shaft,
DC boost, Brushless motor, automatic water cooling, centrifugal impeller, silent,
ultra-quiet operation.

Engineering plastic injection body, built-in automatic water flow sensor switch, high temperature
resistance can be used for water storage bucket gas or electric water heaters and
solar water heaters are designed for hot water circulation or pressurization.

When the faucet is hot, it will improve your bathing hot water condition.
Because old pipelines cannot withstand the pressure of the smallest 1/4Hp horsepower pressurized
motor sold in the market,
The design of the pressure-sensing switch requires constant pressure to be installed in
the rear section of the motor, which is liable to cause cracks in the old water pipe.

Palm Thundaer Pump. 24V DC hot water pressure pump designed for
the old pipeline use 15MX-12NP 65W (1/10Hp horsepower)
Small motor, small volume, large torque, strong water flow, same as 120W pump on the market,
providing enough, supply enough water pressure of the water heater, economical,
spend a small amount of money DIY, you can improve using quality of the hot water.

Bathing is no longer cold and hot!
This "hot water heater dedicated pump 15MX-12NP",
mini model, Palm size, ultra-quiet magnetic motor technology, quiet, power-saving,
24V DC safe, professional soft pressure on the water heater,
It can ensure that the water heater can be used for ignition and heating.

Suitable (gas / electricity) water heater pressure, faucet pressurization,
washing machine into the water, the bathroom faucet, shower head, toilet,
solar hot water delivery booster.

Additional motor mounting brackets, screws and plastic geckos can be fixed in
the appropriate position as required In addition.
No need to drill the wall design, suitable for self-installation, directly installed
under the water heater, directly locked at the inlet end
The wall cold water triangle valve (water outlet) can be used.

Can effectively improve the water heater ignition is not smooth, hot water is
too small and too hot, more suitable for holiday homes, Cars, RVs, campers, huts,
home stays, ships... quietly in use, in line with the needs of the tranquil environment,
Let you use your peace of mind and wash comfortably!

With full voltage transformer 100-240V 50/60Hz AC to 24VDC DC drive, safe,
no electric shock!
The waterproof IP68 body is also safe install in the bathroom.

The latest technology, the smallest, palm size, the only handheld pressure motor
on the market that is equipped with a water flow sensor switch inside the pump body.

Product size: length 135mmX width 70mmX height 90mm mm
Maximum flow: 20 liters per minute
Model: 15MX-12NP
Power: 65W
Head: 13.50 meters
Water pressure: 1Kg/cm2
Power supply: 110V-220V 60Hz power cord 1.2 meters
Applicable voltage: 24V DC3A DC
Weight: about 0.70 kg
Insulation class: Class H
Pipe diameter: 1/2" quarter (15mm)

Installation hot speed focus:
Method I:

1. Do not plug in the power supply first, no power installation.

2. Take an attached (with O-ring) quarter-tap copper connector and wrap the 5-6 turns of
    white tap seal in the clockwise direction.
   Take two movable wrenches (#250 #200) or a universal clamp that can be fixed at one end,
   and lock the attached four-point double-pass copper joint.

3. Wrap the 5-6 turns white seal tape on the wall of the cold water triangle valve.
    Lock the upper (2.) lock.
   The other end of the hex double-pass copper joint is locked as the main mounting support point.

4. Insert the 15MX-12NP inlet into the attached (with O-ring) four-point quick-connect
    copper connector to complete the water inlet installation.

5. First attach the attached 4 points large diameter stainless steel bellows to one end of
    the attached gasket and take a 14mm fixed
   The wrench (fixed hose) and a #200 movable wrench, lock this end bellows (with O-ring)
    hex connecter on the thread of the copper joint (no need to wrap the drain).

6. Attach the attached 4-point large-diameter stainless steel bellows to one end of
    the attached gasket and take a 14mm fixing.
   The wrench and a #200 activity wrench, directly lock the bellows on the screw of
   the cold water inlet of the water heater (No need to wrap the white seal tape).

7. Insert the end of the (5.) (with O-ring) four-point quick-connect copper connector
   into the 15MX-12NP outlet.

8. After the installation is complete, first turn on all the hot water taps supplied by the water heater,
   let the water flow out for 20 seconds.
After plugging in the power plug, let the hot water taps continue to flow for 20 seconds,
then you can turn off the hot water faucet, ready to go, normal use.

Method II:
1. Do not plug in the power supply first, no power installation.

2. Take an attached (with O-ring) quarter-tap copper connector and wrap the 5-6 turns of
    the white tap seal in the clockwise direction.
    Take two movable wrenches (#250 #200) or a universal clamp that can be fixed at one end,
    and lock the attached four-point double-pass copper joint.

3. Wrap 5-6 loops of white seal tape on the water inlet of the water heater's cold water inlet.
    Turn the lock into the upper part (2.) and lock it.
    The other end of the hex double-pass copper joint is locked as the main upside down mounting
    support point.

4. Insert the 15MX-12NP outlet end into the (with O-ring) copper hex connector end attached to (3).
    Complete the outlet installation.

5. First attach the attached 4 points large diameter stainless steel bellows to one end of
    the attached gasket and take a 14mm fixed
   The wrench (fixed hose) and a #200 movable wrench, lock this end bellows (with O-ring)
   hex connecter on the thread of the copper joint (no need tap seal to wrap the drain).

6. Attach the attached 4-point large-diameter stainless steel bellows to one end of the attached
    gasket and take a 14mm fixing.
    The wrench (fixed hose) and a #200 movable wrench, directly lock the bellows to
    the cold water triangle valve on the wall. on the thread (no need to wrap with white seal tape).

7. Insert the end of the (5.) (with O-ring) hex copper connector into the 15MX-12NP outlet.

8. After the installation is complete, first turn on all the hot water taps supplied by the water heater,
    let the water flow out for 20 seconds.
   After plugging in the power plug, let the hot water taps continue to flow for 20 seconds,
   then you can turn off the hot water faucet, normal use.

★Because the motor frame needs to be drilled, please make sure to drill the hole first:
    there is no pipe in the wall before drilling!

Mexa Co., Ltd. 2019 April Product Pump Z

Mexa Co., Ltd.
Aka Halon Co., Ltd.
Tel. +886-2-23657700 Fax.+886-2-23657702
Office: 7F., No. 14 Anmin Street, Xindian District, New Taipei City, Taiwan 231071
Factory: No. 66 Kung Ming 2nd Road, Tsun Tou Liau Industry Area, Tainan, Taiwan Tel.0910-19-6666
挺譽貿易有限公司
赤海龍有限公司
總公司:新北市新店區安民街14號7樓
工廠:台南市安南區總頭寮工業區工明二路66號
挺譽統一編號:05002668
赤海龍統一編號:05002668
工廠登記證號: 67-00-3434



BEFORE	AFTER